Skip to content

TORNADOR® Classic Car Cleaning Tool

3 reviews   |  
Sold out
Original price $199.95 - Original price $199.95
Original price
$199.95 - $199.95
Current price $199.95

TORNADOR® Classic Car Cleaning Tool (Z-010)

United Car Care are proud to be suppliers of the original US patented TORNADOR® Car Cleaning Tools. These Tornador tools are the highest quality on the market today and are the originally designed tools that were invented in the US. TORNADOR® Car Cleaning Tools are designed for professionals and experienced detailers wanting to gain huge speed, efficiency and thorough-quality when it comes to detailing your vehicles interior and exterior surfaces.

  • Cleans and air dries in seconds
  • Tested and approved by industry professionals
  • Low wear and maintenance
  • Heavy-duty construction
  • Low noise emissions

Use the TORNADOR® Car Cleaning Tool on the dashboard, door panels, steering wheel, fabric upholstery, carpet, floor mats, and between seats. The TORNADOR® cleans in tough-to-reach places between seats and in seams. Because it releases so little liquid, surfaces dry quickly. On the exterior, use the TORNADOR® Car Cleaning Tool to clean fabric convertible tops, body seams, wheels, and emblems. There’s no need to scrub. The TORNADOR® does the hard work for you. The TORNADOR® Car Cleaning Tool comes with a green adjustment valve to control the amount of liquid released. Cleaning with the TORNADOR® Car Cleaning Tool is easier and faster than small detailing brushes or swabs. Just spray and watch the dirt release from plastics, rubber, vinyl, and fabrics.

For this device you require an air compressor capable of producing at least 60psi of constant pressure (85psi is the recommended pressure); and no more than 110psi to avoid unnecessary wear.

See the 'Instructions' tab for more information on how to use the TORNADOR® Car Cleaning Tool.

"TORNADOR® tools hold a 90 day limited manufacturer's warranty against manufacturing and part defects."


Wear appropriate hearing and eye protection. Use in well ventilated area. Do not exceed 110 psi. Do not use with acidic, flammable or combustible products. Do not point cleaning tool at face or body. KEEP OUT OF REACH OF CHILDREN. The Tornador cleaning tool requires a minimum air pressure of 75 to 90 psi, constant, for optimum performance.  DO NOT EXCEED 110 psi. NOTE: Constant air supply may vary depending on compressor size and capabilities. Always make sure tank and air lines are free from oil and water contamination.

To clean any surface, dilute the desired cleaner according to label’s directions. Turn the liquid valve straight up and use an overlapping motion as you pass the TORNADOR® Car Cleaning Tool over the surface. If necessary, allow the cleaning liquid to dwell for 10-15 seconds. Use a microfiber towel to absorb excess liquid. Then turn the liquid valve off and use the compressed air to dry the cleaned area.

Cleaning Fabric

1. Remove large debris and vacuum area to be cleaned.
2. Turn liquid air valve to upright position to deliver cleaning solution.
3. Hold cleaning nozzle 1 to 3 inches from area to be cleaned. Fully depress trigger. Begin with overlapping motion over area to be cleaned.
4. Next turn valve to down position using just air and dry the area.

Cleaning Dashboard and Hard Surfaces.

1. Recommended air pressure set at 75 psi
2. Turn liquid valve to straight up vertical position, using a overlapping motion, spray area to be cleaned.
3. Allow cleaning liquid to remain on surface for 10 -15 seconds.
4. Follow with air only by turning valve to the horizontal down position. Begin drying with overlapping motion followed with a soft dry towel.

Maintenance (Important)

• Avoid dropping the gun on the floor, disconnect when not being used.

• Turn liquid valve to the horizontal position after use to avoid dripping from tip.

• Tighten the jar while holding the lid to avoid loosening or stripping gun assembly.

• Keep the cone of the gun clean by removing the cone and rinsing frequently.

NOTE: After every use, place nozzle 2-3 inches into a bucket of soapy water while depressing the trigger once or twice to quickly remove dirt buildup in the cone. This will prevent premature wear.

Out of stock